RDL®

FP-MR2

Message Repeater

SKU: FP-MR2
  • Repeating Single Message
  • Music Quality Message Recording
  • Up to 1.7 Minute Digital Message Storage
  • External Message Actuation
  • Interval Timer to Repeat Message Playback
  • Background Music Input
  • Automatic Voice-Over or Music Ducking
  • Recommended Power Supply ( Not Included )
    PS-24AS (USA)PS-24AX (International)

    Description

    The FP-MR2 is a message repeater that permits electronic storage of a single recording up to one minute forty seconds in duration. This message may be played back manually using an external contact closure to ground or using the front-panel START button. The message may also be played back periodically using the interval timer included in the FP-MR2. A balanced line-level music input allows background music to be connected and the associated input potentiometer allows the installer to set the music level. When message playback is triggered, the music is faded down. At the conclusion of the message, the music level fades back up. A front-panel DIP switch sets the music to fade under the message (-20 dB nominal) or completely off (used for messages containing music). The module output level is a nominal +4 dBu balanced. The output level is indicated on an RDL dual-LED VU meter which is used to set the proper music and recording levels.

    The message may be recorded once, at installation, then played back repeatedly. The message may be re-recorded at any time and is retained when power is removed from the module. The recording input is a standard -10 dBV consumer level unbalanced phono jack. An input level trimmer is provided to set the correct recording level which is indicated on the dual LED meter. The front-panel RECORD ENABLE pushbutton erases the message in memory and enables recording, indicated by the RECORD ENABLE LED. The module begins recording when the START button is pushed and continues until the button is released. The REC LED is illuminated during recording. An integral audio compressor maintains a consistent average recording level over 20 dB input of level variation without significant audible effect on the signal dynamics.

    Specifications


    Recording Input:
    Input:10 kΩ unbalanced
    Input Level:-20 dBV to 0 dBV
    Frequency Response:80 Hz to 12 kHz (± 1.5 dB)
    Noise below +4 dBu:< -65 dB

    Music Input:
    Input:50 kΩ balanced or unbalanced
    Input Level (for +4 dBu out):-18 dBu bal. (-20 dBV unbal.) to +18 dBu bal. (+16 dBV unbal.)
    Frequency Response:30 Hz to 40 kHz (± 1 dB)
    THD+N:< 0.05% (1 kHz)
    Noise below +4 dBu:< -70 dB (unity gain)
    CMRR:>70 dB (50 to 150 Hz)
    Output:150 Ω balanced or 75 Ω unbal.
    Output Level:+4 dBu nominal
    Control Inputs (2):TRIG and DISABLE, Pull to ground, 1 mA
    Control Outputs (2):PLAYING and EOM, Open-collector @ 25 mA
    Ambient Operating Environment:0° C to 55° C
    Power Requirement:24 Vdc @ 60 mA, Ground-referenced
    Dimensions:Height: 1.36 in. 3.46 cm; Width: 3.25 in. 8.26 cm; Length: 5.0 in. 12.7 cm
    Package Type:Cardboard Box
    Package Dimensions:4.375 x 7 x 2.25 in.
    Shipping Weight:0.87 lbs.
    WEEE weight:0.64 lbs.
    Tariff code:8519.81.3020

    Related Products

    Annunciation & Paging
    • FP-CH8

      Chime Generator - 8 Electronic Chimes

    Related Products

    Flat-Pak™ Mounting Accessories
    • FP-HRA

      10.4" Rack Mount for FLAT-PAK Series Products

    • FP-RRB1

      Rear rack rail mounting kit for any FLAT-PAK module

    • FP-RRA

      Rack Adapter FLAT-PAK Series - 19" Fixed

    • FP-RRAH

      Rack Adapter FLAT-PAK Series - 19" Hinged

    DIN Rail Mounting Accessories

    Dimensions

    FP-MR2

    Downloads

    DocumentsFormat
    DatasheetPDF
    CAD FilesUnitsSizeFormat
    Engineering Functional BlockAmerican8.5 KBDXF
    Panel Diagram - FrontAmerican32.38 KBDXF
    Panel Diagram - FrontMetric32.4 KBDXF
    High Res ImagesFormat
    fp-mr2.zipTIF
    Declaration of Conformity
    Download

    Diagrams

    Related Products

    • AMS-PB1

      Momentary SPDT Pushbutton - fits all AMS mounts

    • AMS-SW2

      Rocker Switch DPDT - fits all AMS mounts

    How To Buy

    Direct Dealer Program

    Becoming an RDL direct dealer is quick and easy. To become a direct dealer, your company must meet the following requirements:

    • Must be an A/V contractor, sound contractor or system integrator
    • Must possess a current resale certificate for your state
    Click here to submit a new direct dealer account inquiry

    Buy Online

    CompanyAddressPhoneLink