RDL manufacturers dozens of audio amplifiers for Dante network or conventional audio systems, including a selection of plenum-rated network audio amplifiers. Amplifier models and features: SF-NP35E PoE++ Network to 35 W Mono Audio Amplifier – 70 V or 100 V SF-NP16E PoE+ Network to 16 W Mono Audio Amplifier – 70 V or 100 V […]
Use the SF-ND2 to convert 2 channels of Dante to stereo AES/EBU or S/PDIF inputs of studio monitors or audio recorders without leaving the digital domain. The SF-ND2 is powered via PoE and offers selectable Dante Sample Rates of 44.1 kHz, 48 kHz, 88.2 kHz or 96 kHz. The output is switch selectable to provide […]
The RDL SF-DN4 is used to convert up to two stereo digital audio sources to four Dante channels without leaving the digital domain. The SF-DN4 is PoE powered and offers selectable Dante Sample Rates of 44.1, 48, 88.2 or 96 kHz. The interface automatically detects a valid input on the S/PDIF (optical or coaxial) or AES/EBU […]
The RDL SF-NL2 is a two channel Dante Network to Analog Audio interface designed for use in both installed and portable systems. Each of the two balanced XLR outputs are switch-selectable for Mic or Line level operation and are protected from phantom voltages of up to 48 Vdc. The interface is constructed in a steel […]
The SF-NH1 Dante enabled Stereo Headphone Amplifier can be used as a troubleshooting tool to quickly confirm that a port on a switch is properly configured for the Dante network simply by receiving audio. Setup: Using Dante Controller, apply a static IP address to the amplifier and route an active audio signal to its Left […]
RDL Dante™ Interface and Headphone Amplifiers provide students with personal audio monitoring in the Critical Listening and Post Production Studio As part of a progressive movement to put students ahead of their time with professions in audio engineering and multimedia content creation, Ohio University’s Scripps College of Communication incorporated RDL’s TP-HA1A FORMAT-A™ Headphone Amplifier, along […]
Dual-LED VU meters are provided for each input on the RU-LB2(P) and RU-LB4(P) Dante interfaces to assist the installer in setting the proper input gain. The varying intensity of the green LED indicates a signal level between -11 and +4 dBu. Flashing of the red LED is representative of a VU meter needle swinging above […]
In order for Dante devices to communicate with a computer loaded with DANTE CONTROLLER, the Dante devices and the computer must first be on the same network (in the same range of IP addresses). If not on the same network, Dante Controller will discover and display the names of the devices, but will not be […]
The D SERIES-TPSM2A is a single-gang Decora style two channel microphone preamplifier compatible with other RDL Format-A senders and receivers as well as RDL RU-FN and RU-BNF Dante™ interfaces. The D-TPSM2A provides 48 volt phantom power for condenser microphones and XLR inputs accept signals from both dynamic and condenser microphones. One of the features that […]
RDL Dante™-Enabled audio products with PoE are also equipped with inputs for connection of a local power supply. When connected to a PoE enabled switch and a local power supply the unit will reserve power from the PoE switch but will be powered by the local supply. Should the local power source be interrupted, the […]
The RU-MLB series of Dante bidirectional interfaces provide independently switch-selectable mic or line inputs and line-level outputs. They are available in 2 and 4 channel versions with or without PoE. When an input is set to receive microphone signals, the module provides P48 phantom for operation of balanced condenser microphones. When a condenser microphone is […]
Dante networked audio is ideal for audio systems with large channel counts but it may also be utilized in much smaller systems. It can often be economically viable to utilize Dante to transport one to four channels of audio over an existing Local Area Network when it would otherwise require the installation of dedicated audio […]
Upgrading a sound system to include Dante networked audio doesn’t mean replacing all of the existing power amplifiers. An FP-NML2 Network to Mic/Line Interface will convert 2 Dante audio channels for connection to any device with analog mic or line-level inputs. Each output is equipped with a recessed “MIC/LINE” switch that allows the installer to […]
