RDL®

SF-NP16E

PoE+ Dante to 16 W Mono Audio Amplifier - 70 V or 100 V

SKU: SF-NP16E
  • 16 Watts RMS Constant Voltage Amplifier
  • 70 V or 100 V Output
  • Converts One Dante Network Audio Signal to a Mono Constant Voltage Output
  • Selectable Dante Sample Rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
  • 0 dBFS Input for 16 W Output
  • Automatically limits supply current to protect against PoE+ port shutdown
  • VCA Control on Detachable Terminal Block
  • External Control Using 10 KΩ Potentiometer or 0 to 10 Vdc
  • Compatible with RDL Remote Level Controls
  • Special Software Not Required for Module Setup
  • LED Indicator for Network Sync
  • High-Efficiency Class D Operation
  • Thermal and Short-Circuit Protection
  • Plenum Rated per UL 2043 Standard
Recommended Power Supply
PS-24KS (USA)PS-24KX (International)

Description

The SF-NP16E is an audio power amplifier that converts one Dante network audio channel to a 70 V or 100 V constant voltage amplified output. The output provides 16 watts for a network digital audio level of 0 dBFS. Special software is not required to configure the module.

The SF-NP16E is equipped to operate from a PoE+ enabled network switch. The SF-NP16E may be powered from an external 24 Vdc power supply, available separately.

If a PoE+ powered device instantaneously demands excessive power from a PoE+ port, that port can shut off its output voltage, causing a prolonged disruption of the device operation. The SF-NP16E monitors the amplifier power and limits the current to protect the PoE+ port against shutting down even during extreme feedback or square wave modulation conditions. A red rear-panel PORT PROTECT LED flashes when the SF-NP16E reduces power consumption to prevent shutdown of the PoE+ port voltage.

The SF-NP16E is equipped with an internal VCA for setting the output level. A detachable terminal block provides for the connection of an external 10 KΩ potentiometer or a 0 to 10 Vdc control voltage. The amplifier gain remains at maximum when the VCA input terminal is not connected. RDL remote controls are available to provide single-turn, multi-turn (rotary encoder) or pushbutton (ramp or fixed level selection) user level control. VCA control insures long term noise-free level adjustment.

The module is equipped with both thermal and output short-circuit protection. The high-efficiency Class D output stage produces minimal heat for all levels of expected voice or music modulation. An LED MUTE indicator glows yellow when the output is muted. Valid synchronization to the Dante network is indicated by a green LED visible from the front of the unit.

The SF-NP16E is constructed in a durable, professional all-metal enclosure suitable for free-standing, surface-mounted or rack-mounted operation. This full-featured SYSFLEX® product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. The versatility of SYSFLEX® products adds enormous flexibility in the design and installation of professional A/V systems.

Specifications

Tariff code:8543.70.9910
WEEE weight:2.76 lbs.
Shipping Weight:3.12 lbs.
Package Type:Cardboard Box
Package Dimensions:9.5 x 7 x 2.25 in.
Dimensions:Height: 1.7 in. (4,32 cm); Width: 5.83 in. (14,8 cm); Depth: 6.45 in. (16.38 cm)
Plenum Rating Standard:UL 2043
PoE:Class 4, IEEE 802.3at (PoE +)
Power Requirement:24 Vdc @ 1000 mA, or PoE
Ambient Operating Environment:0° C to 40° C Maximum; 20° C Recommended
VCA:0 to 10 Vdc control, detachable terminal block (compatible with RDL VCA wall controls)
Indicators (3):Front-panel: Sync (green), Amplifier muted (yel), Rear-panel: Port Protect (red), Ethernet Link and Speed (2)
Frequency Response:+0/-3 dB (50 Hz to 20 kHz)
THD+N:< 1% (1 kHz)
Noise:<-90 dB (below max power); <-80 dB (below 1/8 power)
Power Amplifier Output:16 W RMS (70 or 100 V)
Reference Level:0 dBFS = 16 W
Bit Depth Supported:24 bits
Sample Rates Supported:44.1 kHz, 48 kHz (default), 88.2 kHz, 96 kHz
Transmission Rate:100 Mbps
Digital Audio Ethernet Protocol:Dante
Network Connector:RJ45 with Link and Speed indicators

Related Products

Dante®
  • White Wall-Mounted Bi-Directional Mic/Line Dante Interface

    DD-BN22

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • White Wall-Mounted Mic/Line Dante Interface

    DD-BN2M

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • White Wall-Mounted Bi-Directional Mic/Line Dante Interface

    DD-BN2ML

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • White wall-mounted 4x4 Dante interface

    DD-BN31

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 4 x 4

    Customizable Text

  • White Wall-Mounted Bi-Directional 4x2 Dante Interface

    DD-BN40

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 4 x 2

    Customizable Text

  • Black Wall-Mounted 2x2 Dante Interface

    DDB-BN22

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • DDB-BN2M

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • DDB-BN2ML

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • Wall-Mounted Bi-Directional Mic/Line Dante Interface

    DDB-BN31

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 4 x 4

    Customizable Text

  • DDB-BN40

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 4 x 2

    Customizable Text

  • DDS-BN22

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • DDS-BN2M

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • DDS-BN2ML

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 2 x 2

    Customizable Text

  • DDS-BN31

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 4 x 4

    Customizable Text

  • DDS-BN40

    Wall-Mounted Bi-Directional Mic/Line Dante Interface 4 x 2

    Customizable Text

  • FP-NML2

    Network to Mic/Line Interface

  • FP-NML2P

    Network to Mic/Line Interface

  • FP-NML2V

    Network to Mic/Line Interface with VCA

  • FP-NML2VP

    Network to Mic/Line Interface with VCA

  • RU-BNF

    Format-A Bi-Directional Network Interface

  • RU-BNFP

    Format-A Bi-Directional Network Interface

  • RU-FN

    Format-A to Network Interface

  • RU-FNP

    Format-A to Network Interface

  • RU-LB2

    Line-Level Bi-Directional Network Interface

  • Line-Level Bi-Directional Dante Interface

    RU-LB2P

    Line-Level Bi-Directional Dante Interface