TX-LC2
Unbalanced to Balanced Line Combiner
- Mix 2 Unbalanced Audio Signals to Mono Balanced
- Combine Stereo Into Mono with Balanced Output
- Output Gain Trim
- Isolation Between Inputs
- Unbalanced to Balanced Conversion
- High-Quality Audio
TX-LM2
Line Level to Microphone Level Transformer
- Matches balanced 600 Ω phone (or other line) into mic or line input
- Dual outputs:Unbalanced line-level and balanced mic-level
- Frequency response: 20 Hz to 20 kHz (+/- 0.5 dB)
- THD: < 0.05% (1 kHz)
TX-MX2R
Audio Mixer / Distribution Amplifier
- Mix 2 unbalanced mono signals
- Combine stereo into mono
- Gain trim for each input
- Two active isolated outputs from the input signal (s)
- Isolation between inputs
- High-Quality unbalanced audio
TX-PA40D
40 W Stereo Audio Amplifier - 8 Ω, with Power Supply
- Stereo Audio Power Amplifier
- 20 Watts RMS per Channel into 8 Ω – 40 Watts Total
- 15 Watts RMS per Channel into 4 Ω – 30 Watts Total
- Left and Right Unbalanced Phono Jack Inputs
- Switch-Selectable Stereo or Mono Operation
- Studio Quality, Aurally Transparent Compressor/Limiter
- Compressor/Limiter Controls Clipping
- Compressor Produces Maximized Average Output Power
- Compression Enabled Using Input Level Adjustments
- LED to Indicate Audio Compression Threshold
- Outputs Drive 4 or 8 Ohm Speakers
- High-Efficiency Class D Operation
- Thermal and Short-Circuit Protection
- TX-PA40D includes North American Cord; TX-PA40DE excludes Power Cord
TX-PCR1
Paging Controlled Relay
- Switching Functions Controlled by Speaker-Level Source
- Input Accepts Amplified Constant Voltage Signals
- Switch-Selectable Input: 25 V, 70 V, 100 V
- 25 Volt Input Also Accepts 8 Ω Inputs up to 75 Watts
- Transformer-Isolated Input
- Front-Panel Trimmer Provides Sensitivity Adjustment
- Signal Threshold LED Facilitates Sensitivity Adjustment
- Front-Panel Trimmer Provides Release Delay Adjustment
- LED Indicates when Module is Triggered
- Release Delay Adjustable from 3 to 25 Seconds
- Open-Collector Output Active when Module is Triggered
- Switches on Paging or Any Other Amplified Audio Signal
- 8 Amp DPDT Relay Contacts for Switching Speaker Loads
- Ideal for Muting or Switching Primary Speakers During Paging
TX-PD8X
Switching Power Supply Distributor
- Distribution of 24 Vdc Power
- Soft-Start from Switching Supply
- Outputs may be Activated by an External Switch
- Outputs may be Activated by an Open-Collector closure to ground
- Directly Controllable by RDL Remote Controls
- Up to 8 Power Distribution Points
- Voltage Presence Indication
- Reverse Voltage Protection
TX-PSD1
Paging Sound Detector
- Switching Functions Controlled by Speaker-Level Source
- Input Accepts Amplified Constant Voltage Signals
- Switch-Selectable Input: 25 V, 70 V, 100 V
- 25 Volt Input Also Accepts 8 Ω Inputs up to 75 Watts
- Transformer-Isolated Input
- Front-Panel Trimmer Provides Sensitivity Adjustment
- Signal Threshold LED Facilitates Sensitivity Adjustment
- Front-Panel Trimmer Provides Release Delay Adjustment
- LED Indicates when Module is Triggered
- Release Delay Adjustable from 3 to 25 Seconds
- Open-Collector Output Active when Module is Triggered
- Switches on Paging or Any Other Amplified Audio Signal
TX-RA5
TX Series 19" Racking System - 5 modules 1RU
- Mounts up to 5 RDL TX™ Series Modules in a 19″ Rack
- Occupies One RU in a 10.4″ Rack
- All-Steel Construction
TX-TP1PW
Power Inserter - Twisted Pair - 1 set of outputs - Signal loop-through
- Power Remote Senders and Receivers from Convenient Location
- 24 Vdc Power Input on dc Power Jack or Detachable Terminal Block
- Blue Power LED Shows Module is Receiving Power
- Green LED Indicates Correct dc Output Voltage on RJ45s
- Two Associated RJ45 Jacks Provide Power Output
- Receiver May Be Powered From One RJ45 Jack
- Sender May Be Powered From One RJ45 Jack
TX-TP4PW
Power Inserter / Signal Breakout
- Power Remote Senders and Receivers from Convenient Location
- 24 Vdc Power Input on dc Power Jack
- Blue Power LED Shows Module is Receiving Power
- Green LED Indicates Correct dc Output Voltage on RJ45s
- Four Associated RJ45 Jacks Provide Power Output
- Pairs A, B and C are Connected Between all Four RJ45 Connectors
- Power up to Three High-Current Format-A Receivers
TX-TPR1A
Active Single-Pair Receiver - Twisted Pair Format-A - Balanced line output
- Single -10 dBV Unbalanced or +4 dBu Balanced Output
- Phono Jack and Detachable Terminal Block Outputs
- Switch Selects which Pair (A, B or C) Feeds the Output
- Signal and Power Pair Pass-Through to LOOP OUT Jack
- Powered Locally or Remotely through RJ45 Jack
- Fused Local Power Feeds all Modules Connected to RJ45s
- Local Power Input on Terminal Block or dc Power Jack
- Blue LED Indicates Module is Powered
- Daisy-Chain with Additional Format-A Receivers
- Studio-Quality Precision Active Balanced Circuitry
TX-TPR3A
Active Three-Pair Receiver - Twisted Pair Format-A - Balanced line outputs
- Three -10 dBV Unbalanced or +4 dBu Balanced Outputs
- Phono Jack and Detachable Terminal Block Outputs
- Audio Outputs for All Three Pairs (A, B and C)
- Utilizes All Three Format-A Pairs
- Powered Locally or Remotely through RJ45 Jack
- Local Power Feeds all Modules Connected to INPUT
- Wiring Fault Protection by Automatic Resetting Fuse
- Local Power Input on Terminal Block or dc Power Jack
- Blue LED Indicates Module is Powered
- Studio-Quality Precision Active Balanced Circuitry
TX-TPR6A
Passive Single-Pair Receiver - Twisted Pair Format-A - Balanced audio line output
- Single Unbalanced or Balanced 10 kΩ Audio Output
- Output on Detachable Terminal Block or Phono Jack
- +4 dBu Balanced Output; -10 dBV Unbalanced Output
- Switch Selects which Pair (A, B or C) feeds the Output
- Signal and Power Pair Pass-Through to LOOP OUT Jack
- Passive Circuitry Does Not Require Power
- Galvanic Isolation Provided for Both Outputs
- Daisy-Chain with Additional Format-A Receivers
TX-TPS1A
Active Single-Pair Sender - Twisted Pair Format-A - Balanced line input
- Single -10 dBV Unbalanced or +4 dBu Balanced Input
- Phono Jack and Detachable Terminal Block Inputs
- Switch Selects which RJ45 Pair (A, B or C) is Fed
- Signal and Power Pair Pass-Through from LOOP IN Jack
- Powered Locally or Remotely through RJ45 Jack
- Fused Local Power Feeds all Modules Connected to RJ45s
- Local Power Input on Terminal Block or dc Power Jack
- Blue LED Indicates Module is Powered
- Daisy-Chain with Single-Pair or Two-Pair Format-A Senders
- Studio-Quality Precision Active Balanced Circuitry
Sign inShopping cart close